Asked by: Delaine Schnittker
home and garden home appliances

How do you replace the drive cable on a Husqvarna lawn mower?

Last Updated: 5th September, 2021


Click to see full answer.

Then, how do you adjust the drive cable on a Husqvarna lawn mower?

There is a turnbuckle on the drive control housing to increase tension on the drive cable.

  1. Turn the unit off, disconnect the spark plug wire from the plug.
  2. Rotate the turnbuckle on drive control to increase the drive speed.
  3. Operate the mower to test drive speed, readjust as required.

Also Know, what is a lawn mower zone control cable? Part Information. This zone control cable (part number 582991501) is for lawn mowers. Zone control cable 582991501 stops the engine when you let go of the handle. Wear work gloves to protect your hands during this repair.

Consequently, how do I adjust the cable on my lawn mower?

How to Replace & Adjust the Throttle Cable on a Lawnmower

  1. Remove the cable housings using a pair of pliers. The housings will swivel off the base and slide down the cable.
  2. Thread the cable wire through the housing.
  3. Slide the cable through the housing and then into the handle unit to attach it to the throttle handle.
  4. Test the tension by replacing the throttle.

How do you tighten the cord on a self propelled lawn mower?

How to Adjust the Drive Cable on a Toro Self-Propel Mower

  1. Turn off the mower. Locate the self-propelled drive cable support bracket.
  2. Loosen the cable support nut, using an adjustable wrench. Turn the nut counter-clockwise until it is loose.
  3. Pull down on the cable with your fingers, toward the mower deck.
  4. Start the mower to test the self-propel function.

Related Question Answers

Xaira Anuncibai


How do you adjust the handle on a Husqvarna lawn mower?

Husqvarna lawn mower user manual.

for raising or lowering the handle.
  1. Remove upper handle and all wire tie(s) securing.
  2. Remove hairpin cotters from lower handle bracket.
  3. Squeeze lower handle in to remove it from mounting.
  4. Turn lower handle over to raise or lower handle.
  5. Squeeze lower handle in and po si tion holes onto.

Loinaz Urrustarazu


Can you adjust the speed on a self propelled lawn mower?

It goes way to fast and the booklet says the "engine" speed cannot be adjusted. There has to be some way to adjust the speed to slow the mower down to cut the lawn.

Abdul Sango


How do I adjust my Husqvarna?

How to Adjust a Husqvarna Carburetor
  1. Set the Husqvarna chain saw on a level surface.
  2. Start the chain saw and allow the engine to warm for five minutes.
  3. Turn the screw with the "L" stamp clockwise with a screwdriver until the screw stops.
  4. Place the screwdriver on the screw with a "T' stamp.

Kadda Orbach


How do you change the drive belt on a Husqvarna hu800awd?

How to Remove a Drive Belt for a Husqvarna HU800AWD
  1. Turn the lawn mower on its side with the air filter and carburetor up.
  2. Remove the blade bolt, lock-washer, hardened washer, and blade.
  3. Remove the debris shield.
  4. Remove the side bumper.
  5. Remove the rear baffle.
  6. Disconnect the return spring from the rear baffle/rear gearcase belt keeper.

Dita Restolho


Why is my Husqvarna lawn mower not starting?

A clogged carburetor is most commonly caused by leaving fuel in the lawn mower for a long period of time. This sticky fuel can clog up the carburetor and prevent the engine from starting. If the carburetor is clogged, try cleaning it with carburetor cleaner.

Dodie Cigano


Can you push a self propelled lawn mower?

Yes, you can push a self propelled lawn mower, it won't damage the transmission in any way. It may be difficult to do so, self propelled mowers are a little heavier than a regular push mower.

Agoney Nishit


Why does my self propelled mower stopped propelling?

If the transmission pulley is spinning, but the lawn mower wheels don't turn, this indicates that the transmission is defective. The transmission is not repairable—if the transmission is defective, you must replace it. The transmission is powered by the drive belt, and the drive belt connects to the engine crankshaft.

Laida Zakaroff


What is Husqvarna Auto walk?

AUTOWALK™ 2 is Husqvarna's two-hand speed control system that makes it possible to shift between using your right or left hand when using one of their petrol lawn mowers. This is ideal when mowing awkwardly shaped lawns and around objects.

Lisa Hofgen


How does a self drive lawn mower work?

Self-propelled lawnmowers work on a drive system (making them vehicle-like) that requires the operator to squeeze a bar (called a "bail") on the handle to engage the mower. After that, the mower moves forward on its own (you don't have to push it).

Oury Avella


How do you turn off a self propelled lawn mower?

How to Disconnect the Self-Propelled Unit From the Lawnmower
  1. Disconnect the spark plug wire from the mower's spark plug to disable the engine.
  2. Remove the screws that hold the transmission cover onto the top of the mower with a screwdriver.
  3. Locate the setscrew between the transmission and pulley.
  4. Place the mower on its side so the air cleaner faces upward.

Zacaria Paramoshkin


How do you change the speed on a Craftsman self propelled lawn mower?

A single lever near the back right wheel allows you to adjust the height of all four wheels at once. If you don't have a self-propelled Craftsman mower, hold your hands firmly on the handlebars and walk faster to speed up, or walk slower to slow down.